[Ovmsdev] Car firmware: 1.2.5
William Petefish
william.petefish at gmail.com
Sun May 13 14:11:06 HKT 2012
I'll do a logging session on monday.
I've actually got 2 tools that I can use. (logic analyzer w/ data logging
and analyzation functionality, and my CAN-USB which has CAN Hacker which
can log and can give individual messages.)
William
On Sun, May 13, 2012 at 12:14 AM, Mark Webb-Johnson
<mark at webb-johnson.net>wrote:
> William,
>
> If you get a chance, just get a full log dump of that can bus the OVMS
> uses. Textual is fine (csv, whatever) and a timestamp would be useful. I'm
> willing to do the analysis, I just need a can dump containing home link
> transmission messages.
>
> Useful if you can key the home link to some other recognizable event. For
> example, open passenger door, activate home link, close passenger door. We
> then need only to look at a short part of the log, looking for something
> new. Car doors are good, but also trunk and hood. Keep clear of charge port
> because opening that triggers all sorts of other stuff. Also good if you
> can do it a few times. Whichever, let us know the exact sequence (eg; open
> left door @15sec in, activate home link 1 about 2 seconds later, then
> closed left door, did this three times, etc) and how you keyed the event.
>
> If you want to look for the event itself, all we know is at:
>
>
> https://raw.github.com/markwj/Open-Vehicle-Monitoring-System/master/vehicle/Car%20Module/canbus_notes.txt
>
> A sub-message <B1> on ID#102 is the most likely, as those are messages
> from the VDS.
>
> Regards, Mark
>
> On 13 May, 2012, at 12:37 PM, William Petefish <william.petefish at gmail.com>
> wrote:
>
> I have CAN Hacker on my netbook. I also have a USB-CAN interface. I don't
> know how much time I'll have in the next week or so. All bets are off, but
> I'll try to get some work done next week.
>
> William
>
> On Sat, May 12, 2012 at 9:24 PM, Mark Webb-Johnson <mark at webb-johnson.net>wrote:
>
>> To track down the homelink messages, we'd need someone with both homelink
>> and a way to capture can bus messages (a USB CAN bus tool).
>>
>> I have the tool, but the cars in hong kong have no homelink module
>> installed.
>>
>> The capture itself should be fairly simple. I'd put money on the messages
>> being on ID#102, and there are a very limited number of those messages.
>>
>> Regards, Mark.
>>
>> On 13 May, 2012, at 12:25 AM, 911carrera4 wrote:
>>
>> Hallo everybody****
>> ** **
>> I was able to configurate the HomeLinks on both our EU-Roadsters (my
>> wife‘s and mine). We have two garages with two doors. For the opening of
>> the doors we use a german product called maraton 1100SL (the company is
>> Sommer, D- 73230 Kirheim)****
>> ** **
>> I did it in two steps:****
>> 1. I sent the code from the garage remote control to the Roadster
>> (as described in the Tesla manual „How to configurate HomeLink“)****
>> 2. I paired (linked) the HomeLink from the Roadster to the control
>> panel of the garage door (as described in the manual you get with your
>> garage door control pannel)****
>> ** **
>> That‘s all. It works good, but the range is a bit shorter than with the
>> original remote control.****
>> ** **
>> The frequency of the System is 868Mhz (without external antenna).****
>> ** **
>> Piotr****
>> ** **
>> ** **
>> *Von:* ovmsdev-bounces at lists.teslaclub.hk [mailto:
>> ovmsdev-bounces at lists.teslaclub.hk] *Im Auftrag von *David Morse
>> *Gesendet:* Samstag, 12. Mai 2012 17:22
>> *An:* OVMS Developers
>> *Betreff:* Re: [Ovmsdev] Car firmware: 1.2.5****
>> ** **
>> Thank you all for working on this. I'm just an end user so can't
>> contribute much more than comments but am looking forward to the cool down
>> feature. I am curious though, does anyone have evidence that the cool down
>> feature in beneficial? If so, I wonder why this is something Tesla never
>> implemented. Thanks. ****
>> ** **
>> David
>>
>> Sent from my iPad****
>>
>>
>> On May 12, 2012, at 9:33 AM, "Oliver Weidmann" <oliver at sdds.ch> wrote:***
>> *
>>
>> A guy from Switzerland has a working homelink. I’ll have to ask him how
>> he managed to successfully pair it…****
>> ****
>> *Von:* ovmsdev-bounces at lists.teslaclub.hk
>> [mailto:ovmsdev-bounces at lists.teslaclub.hk] *Im Auftrag von*Pierre Uhl
>> *Gesendet:* Samstag, 12. Mai 2012 13:39
>> *An:* 'OVMS Developers'
>> *Betreff:* Re: [Ovmsdev] Car firmware: 1.2.5****
>> ****
>> Re Homelink****
>> ****
>> The Homelink in Europe is disabled, because the frequency in Europe is
>> not the same like in the US (FCC regulation?).****
>> ****
>> ****
>> *Von:* ovmsdev-bounces at lists.teslaclub.hk
>> [mailto:ovmsdev-bounces at lists.teslaclub.hk] *Im Auftrag von*Mark
>> Webb-Johnson
>> *Gesendet:* Samstag, 12. Mai 2012 13:22
>> *An:* OVMS Developers
>> *Betreff:* [Ovmsdev] Car firmware: 1.2.5****
>> ****
>> ****
>> I've committed to github car firmware v1.2.5.****
>> ****
>> Changes since v1.2.2 include:****
>> ****
>>
>> - Support multiple vehicle configurations - TeslaRoadster and
>> VoltAmpera****
>> - New LED indication scheme, and net driver tidy-ups****
>> - Auto-support Tesla Roadster v1.5 cars****
>> - Issue #38 - Prevent user from locking car if car is ON****
>> - Issue #39 - Alert (SMS/PUSH) if trunk is opened while in valet mode*
>> ***
>>
>> ****
>> Please don't get too excited - this doesn't support Volt/Ampera yet -
>> we're just laying the ground work for that support, as some European
>> developers are about to start work on it.****
>> ****
>> I don't think this release will make it to end-users in its current form.
>> I'm still working on some features to go in, including:****
>> ****
>>
>> 1. Drive logging****
>> 2. Charge logging****
>> 3. Timed (delayed) charging mode commands****
>> 4. Timed charging status feedback****
>> 5. Complete-charging-by charging mode****
>> 6. Cooldown****
>> 7. Moving digital speedo out of experimental and make it available in
>> production units****
>>
>> ****
>> Items [1], [2] and [3] are relatively easy and what I'm working on now.**
>> **
>> ****
>> Item [4] is tricky because we haven't found the status update message on
>> the bus yet. Still looking. Item [5] needs the algorithm and lookup table.
>> Item [6] is easy to do, but needs the thresholds defined (what battery
>> temperature to cooldown from, what battery temperature to stop cooldown at,
>> and what current/voltage to use for cooldown).****
>> ****
>> Item [7] seems reasonable now, given the number of cars now using the
>> digital speedo feature and the complete lack of issues seen with it.****
>> ****
>> I notice there was some discussion on the TMC forum about homelink
>> control. That would be pretty easy to do, but we don't have homelink
>> modules here in Hong Kong, and I don't have the can bus codes. They are
>> probably easy to find on ID#102. If someone with a usb-can and a homelink
>> adaptor wants to get the codes, I'm very willing to put them in. It
>> certainly is a cool feature.****
>> ****
>> So, I'm not sure what will make it into what release, when.****
>> ****
>> This v1.2.5 release is definitely developers-only, and intended to check
>> stability of the modem driver revisions and usability of the new LED
>> feedback scheme. It is fully backwards-compatible with v1.2.2, and you can
>> upgrade/downgrade firmware as you need.****
>> ****
>> It is in my car now, and seems to be ok. I would be grateful if
>> developers with some time could try it out and let me have feedback on
>> overall stability and usability of the new LED indication scheme.****
>> ****
>> I've got a little youtube video demonstrating this:****
>> ****
>>
>> http://www.youtube.com/watch?v=MdsB8qK6beY****
>>
>> ****
>> The new LED indication scheme is as follows:****
>> ****
>>
>> 1. When first powered on, the red led stays on, and the green led
>> blinks the version of firmware in the module (e.g.; 1, 2, 5). After that,
>> it enters normal mode.****
>> 2. In normal mode, the green led is used to indicate the state, and
>> the red led is used to indicate the last error.****
>> 3. If the modem needs to be reset, both red and green leds are turned
>> on for the couple of seconds it takes to reset the modem.****
>>
>> ****
>> The following states are defined:****
>>
>> // LED MODES
>> #define NET_LED_WAKEUP 10 // Attempting to wake up the modem
>> #define NET_LED_INITSIM1 9 // Checking SIM card insertion status
>> #define NET_LED_INITSIM2 8 // Checking SIM card PIN status
>> #define NET_LED_INITSIM3 7 // Initialising modem
>> #define NET_LED_COPS 6 // COPS initialisation
>> #define NET_LED_NETINIT 5 // GPRS NET initialisation
>> #define NET_LED_NETAPNOK 4 // GPRS APN is OK, final init
>> #define NET_LED_NETCALL 3 // GPRS Network call
>> #define NET_LED_READY 2 // READY state
>> #define NET_LED_READYGPRS 1 // READY GPRS state****
>>
>> ****
>> The normal behavior is it will start at 10 green blinks and count down to
>> 2 (GSM only) or 1 (GPRS). If GPRS lock is lost, but GSM is still up, the
>> green will blink 1.****
>> ****
>> The followed error codes are defined:****
>>
>> // LED ERRORS
>> #define NET_LED_ERRLOSTSIG 1 // Lost signal
>> #define NET_LED_ERRMODEM 2 // Problem communicating with modem
>> #define NET_LED_ERRSIM1 3 // SIM is not inserted/detected
>> #define NET_LED_ERRSIM2 4 // PIN lock on the SIM
>> #define NET_LED_ERRCOPS 6 // COPS GSM lock could not be obtained
>> #define NET_LED_ERRGPRSRETRY 7 // Error (maybe temp) during GPRS init
>> #define NET_LED_ERRGPRSFAIL 8 // GPRS NET INIT failed****
>>
>> ****
>> The error code is cleared (red led turned off) once everything is ok.****
>> ****
>> Regards, Mark.****
>> ****
>>
>> _______________________________________________
>> OvmsDev mailing list
>> OvmsDev at lists.teslaclub.hk
>> http://lists.teslaclub.hk/mailman/listinfo/ovmsdev****
>>
>> _______________________________________________
>> OvmsDev mailing list
>> OvmsDev at lists.teslaclub.hk
>> http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
>>
>>
>>
>> _______________________________________________
>> OvmsDev mailing list
>> OvmsDev at lists.teslaclub.hk
>> http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
>>
>>
> _______________________________________________
> OvmsDev mailing list
> OvmsDev at lists.teslaclub.hk
> http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
>
>
> _______________________________________________
> OvmsDev mailing list
> OvmsDev at lists.teslaclub.hk
> http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.teslaclub.hk/pipermail/ovmsdev/attachments/20120513/f3d8d759/attachment-0001.html>
More information about the OvmsDev
mailing list