Ok, MUCH better. CAN3 is back to working again! No evidence of the transmit overrun problem, and the frames are about 50ms apart, so I think your transmit changes are working. I'm running 500k BAUD.
I'll let it run for a while, just to check stability. But so far, Yea!
Greg
Michael Balzer wrote:
I've added another minor change to avoid TX lockups if the bus is lost (i.e. disconnected). Also CMD_READ_RXBUF actually clears the interrupt flag itself, so we can skip the additional BITMODIFY call.
The internal ESP32 CAN controller (SJA1000) unfortunately only has one TX buffer. I'm having performance issues with the TX speed on that, it's not consistently sufficient high to get the Twizy charge control working reliably. Not sure yet if that's caused by the CAN controller, the driver or the RTOS.
Regards,
Michael
Am 31.12.2017 um 14:33 schrieb Geir Øyvind Vælidalo:
I’ve been looking into what’s happening with the interrupt/queue this morning and your fix makes more sense than my suggestion. It could potentially fix the problem with the buffer filling up.Unfortunately my wife is using the car so I can’t test this yet,
Geir
31. des. 2017 kl. 10:54 skrev Michael Balzer <dexter@expeedo.de>:
Geir & Greg,_______________________________________________
first of all, I did an over-optimization mistake in the RxCallback: the return after fetching the frame must always be true -- fix is pushed.
That has caused frames to get lost so you should apply this fix first.
Am 31.12.2017 um 01:00 schrieb Geir Øyvind Vælidalo:
I did a test where I created three counters.One went into MCP2515_isr and counts every interrupt.One was added as the first code line in mcp2515::RxCallback.And the third one was added to RxCallBack, but right before we read the CAN frame via SPI that will end up in IncomingFrame. I.e. should be a count of every CAN frame.
This is what I got:
OVMS > can can2 statusCAN: can2Mode: ActiveSpeed: 100000Rx pkt: 82MCP2515_isr: 239RxCallback1: 320RxCallback2: 295Rx err: 0Tx pkt: 0Tx err: 0Err flags: 0x2040
These numbers puzzles me. Shouldn’t RxCallback1 and RxCallback2 be less or equal to MCP2515_isr? Where does these extra 81 calls come from? I’m missing something here...
No, that's expected behaviour. The MCP2515 has two RX buffers plus error conditions. The framework is designed to loop RxCallback over an IRQ event until all buffers and error conditions have been processed, so RxCallback counters should always be >= ISR count.
Also, RxCallback2 is much bigger than Rx pkt, which means not all frames are sent to IncomingFrame.
That's in part due to my bug, but it also can happen under normal conditions, as an error IRQ will also trigger the RxCallback but not return a frame to be processed.
What does the 0x2040 means? And where do that number comes from?
That's constructed in line 293 from the error interrupt flags and the error register. The lower 8 bits are in the image I sent, the upper 8 bits are
// MERRF 0x80 = message tx/rx error
// ERRIF 0x20 = overflow / error state change
Regards,
Michael
-- Michael Balzer * Helkenberger Weg 9 * D-58256 Ennepetal Fon 02333 / 833 5735 * Handy 0176 / 206 989 26
OvmsDev mailing list
OvmsDev@lists.teslaclub.hk
http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
_______________________________________________ OvmsDev mailing list OvmsDev@lists.teslaclub.hk http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
-- Michael Balzer * Helkenberger Weg 9 * D-58256 Ennepetal Fon 02333 / 833 5735 * Handy 0176 / 206 989 26
_______________________________________________ OvmsDev mailing list OvmsDev@lists.teslaclub.hk http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
_______________________________________________ OvmsDev mailing list OvmsDev@lists.teslaclub.hk http://lists.teslaclub.hk/mailman/listinfo/ovmsdev
-- Michael Balzer * Helkenberger Weg 9 * D-58256 Ennepetal Fon 02333 / 833 5735 * Handy 0176 / 206 989 26