I see some issue with:

vehicle/OVMS.V3/components/ovms_webserver/assets/charts.js.gz

Perhaps some build artifact not cleaned up that causes a -dirty?

I’ve tried rebuilding the release-3.3.006 branch and that now gives me 3.3.006-3-g8eeae067.

That should resolve this.

Regards, Mark.

On 1 Jun 2026, at 8:11 PM, Michael Balzer via OvmsDev <ovmsdev@lists.openvehicles.com> wrote:

Greg, Mark,

Greg, you've got "dirty" builds (= built with not yet checked in local changes) installed on both OTA partitions now.

This points to the version currently available on your update server having the "dirty" tag. Mark, I assume that's your server, can you please check?

The OTA system treats a local "dirty" tag as sufficient for triggering an update, also if the version on the server has the same version, so that explains why you get repeated updates: the OTA system doesn't expect a version from the server being "dirty", so will update repeatedly in this case as long as the hour matches.

Regards,
Michael


Am 01.06.26 um 06:02 schrieb Greg D.:
Hi Michael,

All the messages show 3.3.006, with nothing extra, as displayed on the Android app.  Looking at the web-based Status screen, it shows the following:
Hardware: OVMS WIFI BLE BT cores=2 rev=ESP32/1; MODEM SIM7600
Firmware: 3.3.006-dirty/ota_1/eap (build idf v3.3.4-854-g9063c8662 May 18 2026 23:49:43, product v3.1)
Partition type: v3-30 (factory, ota1, ota2, 1MB store)
Partition table: 0x8000
Running partition: ota_1
Boot partition: ota_1
Factory image: 3.1.001
OTA_O image: 3.3.006-dirty
OTA_1 image: 3.3.006-dirty
Since my original message there was another set of 4 download / update messages this past night (5/31 starting at 2:01 am local, UTC -7), so this is as of right now.  I've not been paying attention to the firmware management commands for some time, so no recollection on how to retrieve any of the logs.  What commands do I need to give?

Thanks,

Greg


Michael Balzer via OvmsDev wrote:
Greg,

please be specific about the messages, were all of them naming version "3.3.006"?

Background: there have been multiple releases to EAP over the last days, but only the initial one was "3.3.006" without a suffix.

EAP is currently following EDGE due to the Smart EQ issue still needing changes to the release candidate. The latest update was yesterday, it's now at 3.3.006-57-g2035e13ac.

If you saw no sub version suffixes on later update notifications, do you have some log excerpt covering these update runs?

Regards,
Michael


Am 30.05.26 um 05:19 schrieb Greg D.:
Hi folks,

I had enabled EAP updates some time (years?) ago, and with the recent release of 3.3.006 the module in my Roadster updated.  And updated.  And updated.  Early in the AM of May 29th, the Android app's view of the message log shows 5 pairs of "New OTA firmware 3.3.006 is now being downloaded" followed by "OTA firmware 3.3.006 has been updated (OVMS will restart)".  In the middle of the set is a notice that charging is done (it was actually done many hours before).

This also happened on May 257th, and the 27th.

The module seems to be working otherwise.  Is this expected?  How can I stop it?

I suspect this is has something to do with the image size / partitioning change, but I wasn't following that discussion very closely.

Thanks,

Greg

_______________________________________________
OvmsDev mailing list -- ovmsdev@lists.openvehicles.com
To unsubscribe send an email to ovmsdev-leave@lists.openvehicles.com


_______________________________________________
OvmsDev mailing list -- ovmsdev@lists.openvehicles.com
To unsubscribe send an email to ovmsdev-leave@lists.openvehicles.com


-- 
Michael Balzer * Am Rahmen 5 * D-58313 Herdecke
Fon 02330 9104094 * Handy 0176 20698926

_______________________________________________
OvmsDev mailing list -- ovmsdev@lists.openvehicles.com
To unsubscribe send an email to ovmsdev-leave@lists.openvehicles.com