No issue reports so far. I've released 3.2.016 to "main" on my
server.
Regards,
Michael
Am 06.03.21 um 14:34 schrieb Mark
Webb-Johnson:
Sure. Will do on Sunday.
Mark
Everyone,
I've just tagged the 3.2.016 release, uploaded it to my "eap"
directory and published the info on my site.
Mark, I suggest you do the same on
openvehicles.com.
If no issues turn up, we should aim at the "main" release in
about 1-2 weeks.
Summary of changes:
- New vehicle: VW e-Up via OBD-II Port
(VWUP.OBD)
- New vehicle: MG ZS EV via OBD-II Port (MGEV)
- New vehicle: BMW i3/i3s via OBD-II Port (BMWI3)
- VW e-Up: combined T26A & OBD module, extended standard
metrics coverage,
charge notifications & durations (OBD), enhanced
cabin pre-heating (T26)
- VW e-UP T26A: add climate control and charging detection
- VW e-Up: BMS cell monitoring (@OBD)
- VW e-Up: CCS (DC) charge detection & data
New metrics:
xvu.c.ccs.u -- CCS charger supplied voltage
[V]
xvu.c.ccs.i -- CCS Charger supplied current
[A]
xvu.c.ccs.p -- CCS Charger supplied power
[kW]
- VW e-Up: replaced MFD range based CAC/SOH by charge
coulomb count based
Removed metrics:
xvu.b.cap.range
xvu.b.cap.chg.ah.norm
xvu.b.cap.chg.ah.norm
xvu.b.cap.chg.kwh.norm
xvu.b.cap.chg.kwh.abs
New metrics:
xvu.b.energy.range -- MFD range estimation energy
[kWh]
xvu.b.cap.kwh.range -- … usable battery capacity
derived [kWh]
xvu.b.cap.ah.abs -- Charge coulomb based capacity
[Ah]
xvu.b.cap.ah.norm -- … normalized (usable) [Ah]
xvu.b.cap.kwh.abs -- Charge energy based capacity
[kWh]
xvu.b.cap.kwh.norm -- … normalized (usable) [kWh]
- MG ZS EV: Add Charging Metrics page.
- MG ZS EV: Add support for ms_v_charge_kwh,
ms_v_bat_energy_used and ms_v_bat_coulomb_used metrics
- Volt/Ampera: BMS cell monitoring (CAN1 polling), fast CAN
polling when waking up,
estimated range gets from CAN instead of calculation,
lock/unlock status processing fixed for Volt 14MY;
New standard metrics:
trip (this charge), energy used (this charge), HV
battery capacity (CAC, Ah),
transmission temp, doors, trunk, hood, lightings;
- Volt/Ampera: new xva metrics:
xva.v.p.trip.ev = trip using electric, km;
xva.v.e.fuel = fuel tank level, %;
- Renault Twizy: new metrics to reflect extended lock &
valet modes:
xrt.v.e.locked.speed -- Speed limit [kph] set for
Twizy lock mode
xrt.v.e.valet.odo -- Odometer limit [km] set for
Twizy valet mode
- Renault Twizy: support additional OBD/UDS request types
& arguments on "xrt obd request"
- ZOE: BMS cell monitoring (PH1)
- SmartED: add Drivmode for Brabus
- Nissan Leaf: invert batt current sign to match standard
metrics definition, populate charger power/efficiency
- Vehicle framework: generic single OBD2/UDS request shell
command & API call
New commands:
obdii can[1-4] request device [-t<timeout_ms>]
[-e] txid rxid request
obdii can[1-4] request broadcast [-t<timeout_ms>]
request
- BMS: optional cell voltage & temperature logging
New configs:
[vehicle] bms.log.voltage.interval Interval [s] for
cell voltage logging, default 0=disable
[vehicle] bms.log.temp.interval Interval [s] for
cell temperature logging, default 0=disable
- BMS: detection of inconsistent voltage series by gradient
& stddev average deviation
thresholds, added pack metrics to battery monitor web
UI, change cell warning & alert
thresholds to be applied exceeding stddev level
New metrics:
v.b.p.voltage.grad Cell voltage -
gradient of current series [V]
New configs:
[vehicle] bms.dev.voltage.maxgrad Max gradient for a
valid series
[vehicle] bms.dev.voltage.maxsddev Max stddev
deviation from average for valid series
- Notifications: added optional long term trip & grid
(charge/generator session) server logs.
See https://docs.openvehicles.com/en/latest/userguide/notifications.html
for details.
New configs:
[notify] log.trip.storetime Trip log storage time in
days, 0/empty = off (default)
[notify] log.trip.minlength … minimum trip length in
km, default 0.2 km
[notify] log.grid.storetime Grid log storage time in
days, 0/empty = off (default)
- Metrics: extended reboot persistence: most vehicle state
and long term counter
metrics will now retain their values over a reboot (e.g.
OTA update)
- Metrics: new standard metrics for grid integration (V2G) /
generator role
New standard metrics:
v.c.kwh.grid Energy drawn from grid during
running session
v.c.kwh.grid.total Energy drawn from grid total
(life time)
v.g.generating True = currently delivering
power
v.g.climit Maximum generator input current
(from battery)
v.g.current Momentary generator input
current (from battery)
v.g.duration.empty Estimated time remaining for
full discharge
v.g.duration.range … for range limit
v.g.duration.soc … for SOC limit
v.g.efficiency Momentary generator efficiency
v.g.kwh Energy sum generated in the
running session
v.g.kwh.grid Energy sent to grid during
running session
v.g.kwh.grid.total Energy sent to grid total
v.g.limit.range Minimum range limit for
generator mode
v.g.limit.soc Minimum SOC limit for generator
mode
v.g.mode Generator mode (TBD)
v.g.pilot Pilot signal present
v.g.power Momentary generator output power
v.g.state Generator state (TBD)
v.g.substate Generator substate (TBD)
v.g.temp Generator temperature
v.g.time Duration of generator running
v.g.timermode True if generator timer enabled
v.g.timerstart Time generator is due to start
v.g.type Connection type (chademo, ccs,
…)
v.g.voltage Momentary generator output
voltage
- TPMS: metrics rework & standard alert notifications on
new v.t.alert metric.
Replaced metrics…
v.tp.fl.p TPMS front left pressure
v.tp.fl.t TPMS front left temperature
v.tp.fr.p TPMS front right pressure
v.tp.fr.t TPMS front right temperature
v.tp.rl.p TPMS rear left pressure
v.tp.rl.t TPMS rear left temperature
v.tp.rr.p TPMS rear right pressure
v.tp.rr.t TPMS rear right temperature
…by…
v.t.pressure TPMS tyre pressures vector
(fl,fr,rl,rr)
v.t.temp TPMS tyre temperatures vector
New standard metrics:
v.t.alert TPMS tyre alert levels
[0=normal, 1=warning, 2=alert]
v.t.health TPMS tyre health states
- New standard metrics for total (life time) energy and
coulomb
- Events: added automatic events on v.e.aux12v changes.
New events:
vehicle.aux.12v.on
vehicle.aux.12v.off
- Location: add metric for name of current location
New metrics:
v.p.location -- Name of current location if
defined
- Server V3 improvements:
a) On first connection to MQTT broker we used to send
all metrics. Now
we only send metrics for which we have a value.
b) New config settings:
"updatetime.on" which sets updatetime when the car
is on (driving)
"updatetime.charging" which sets updatetime when
the car is charging
"updatetime.awake" which sets updatetime when the
car is awake
If unset the server uses the "idle" or "connected"
interval as before
c) New config setting "updatetime.sendall". If you set
this we will publish
_all_ valid metrics at this interval. Helpful to keep
a steady flow of
values for charting.
PLEASE NOTE: These settings will increase OVMS' data
usage.
- Wifi: option to immediately disconnect/reconnect on bad
signal level
New config:
[network] wifi.bad.reconnect [bool], default no
- WiFi: replace fixed scan times by config instances
New configs:
[network] wifi.scan.tmin Min scan time per
channel [ms], default 120 ms
[network] wifi.scan.tmax Max scan time per
channel [ms], default 120 ms
- Updated wolfssh and wolfssl so the restriction of clients
to use
aes128-cbc cipher is no longer required.
Regards,
Michael
--
Michael Balzer * Helkenberger Weg 9 * D-58256 Ennepetal
Fon 02333 / 833 5735 * Handy 0176 / 206 989 26
_______________________________________________
OvmsDev mailing list
OvmsDev@lists.openvehicles.com
http://lists.openvehicles.com/mailman/listinfo/ovmsdev
_______________________________________________
OvmsDev mailing list
OvmsDev@lists.openvehicles.com
http://lists.openvehicles.com/mailman/listinfo/ovmsdev
--
Michael Balzer * Helkenberger Weg 9 * D-58256 Ennepetal
Fon 02333 / 833 5735 * Handy 0176 / 206 989 26