<html><head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body><div>I would try RE Tools too to see if there are realy no CAN messages.</div><div><br></div><div>It would be great if you could proof me wrong. Would save us heaps of work ...</div><div><br></div><div>Chris</div><div><br></div><div>(dev)marxx</div><div><br></div><div>Am Donnerstag, den 30.07.2020, 16:43 +0200 schrieb Soko:</div><blockquote type="cite">
<p>Ahhh OK, I've found OvmsVehicle::virtual void TickerXXX(uint32_t
ticker);<br>
Got it! This was exactly my issue as I didn't know about any
function which gets called regularly so I could check something
like this...<br>
It's not an ideal situation though: I just can slow down the poll
after my fail-counter gets too high as I need to check when the
car gets powered again. So all I can do is polling, lets say every
60 secs when the car is off, and increase it once its on. But
there is now way around this 60-sec polling if the only thing I
can do is poll :(<br>
</p>
<p>Afaik there is only the sharkcow's list below, reverse engineered
by him from ODBeleven.</p>
<p>(dev)marxx exlpained to me: There is a gateway between the
CAN-Buses and the OBD Connector in all VW-AG vehicles which only
replies to polls and also acts as security gateway if you want to
write to the buses.</p>
<p>So I think I cannot really do a can log or use re tool as the OBD
interface stays quiet if I'm not polling it...</p>
<p>And as there is no other vehicle from VW,Seat,Skoda,Audi,etc. in
OVMS. So I have no cheat-sheet :(</p>
<p>Anyhow... I would need to poll one ECU (is this the correct
therm?) which doesn't shuts down... or maybe the issue is the
OBD-gateway shutting down.<br>
</p>
<p>What do you think?</p>
<p>Soko<br>
</p>
<div class="moz-cite-prefix">On 30.07.2020 16:17, Michael Balzer
wrote:<br>
</div>
<blockquote type="cite" cite="mid:429f9711-74bd-828c-0c9c-3872f9b0bfac@expeedo.de">
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
Soko,<br>
<br>
nice progress :-)<br>
<br>
If you can't detect vehicle state by listening to regular status
CAN frames, you can check the time since the last poll reply in
the per second ticker.<br>
<br>
As poll replies normally come in fast, you should be able to
detect a switch-off by a small timeout, say 3 seconds… probably
need to add a counter, as a single poll may get lost / ignored.<br>
<br>
CAN tx errors can be caused by other issues as well, so should
generally not be interpreted that way.<br>
<br>
But… are you sure there are no status frames on the bus? Have you
done a can log or tried the re tool?<br>
<br>
Regards,<br>
Michael<br>
<br>
<br>
<div class="moz-cite-prefix">Am 30.07.20 um 14:43 schrieb Soko:<br>
</div>
<blockquote type="cite" cite="mid:dfef03ed-b0e1-1fda-7eab-de5b6e49cc67@soko.cc">Hi guys,
<br>
<br>
Want to report success on connecting and reading my VW e-Up via
OBD cable using the Poller. As you can see in the screenshot of
the log attached I get an IncomingPollReply(..) call and an SoC
value of 33.333% <br>
<br>
Once I turn of the ignition and lock the car though I don't get
any replies no more (line D 793813) and then I get can1
errors... I'm polling with 10 seconds intervall. <br>
<br>
I know that this is as it should be... but my issue is: I don't
have any way to know if the ignition is on, the key is in, the
car is running, the car is charging as the PIDs are not known
for such values (afaik by the lists of sharkcow <a class="moz-txt-link-freetext" href="https://www.goingelectric.de/wiki/Liste-der-OBD2-Codes/" moz-do-not-send="true">https://www.goingelectric.de/wiki/Liste-der-OBD2-Codes/</a>).
<br>
<br>
So what would be the best approach to change the different
polling states? Can I somehow get called (in my vehicle-class)
if an can-error is thrown? Then I would increase the poll
frequency. <br>
<br>
Any suggestions? <br>
<br>
thanks <br>
<br>
Soko <br>
<br>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">_______________________________________________
OvmsDev mailing list
<a class="moz-txt-link-abbreviated" href="mailto:OvmsDev@lists.openvehicles.com" moz-do-not-send="true">OvmsDev@lists.openvehicles.com</a>
<a class="moz-txt-link-freetext" href="http://lists.openvehicles.com/mailman/listinfo/ovmsdev" moz-do-not-send="true">http://lists.openvehicles.com/mailman/listinfo/ovmsdev</a>
</pre>
</blockquote>
<br>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">_______________________________________________
OvmsDev mailing list
<a class="moz-txt-link-abbreviated" href="mailto:OvmsDev@lists.openvehicles.com" moz-do-not-send="true">OvmsDev@lists.openvehicles.com</a>
<a class="moz-txt-link-freetext" href="http://lists.openvehicles.com/mailman/listinfo/ovmsdev" moz-do-not-send="true">http://lists.openvehicles.com/mailman/listinfo/ovmsdev</a>
</pre>
</blockquote>
<pre>_______________________________________________
OvmsDev mailing list
<a href="mailto:OvmsDev@lists.openvehicles.com">OvmsDev@lists.openvehicles.com</a>
<a href="http://lists.openvehicles.com/mailman/listinfo/ovmsdev">http://lists.openvehicles.com/mailman/listinfo/ovmsdev</a>
</pre></blockquote></body></html>