<div dir="ltr">Brilliant - thanks Mark.<div><br></div><div>My OVMS has been offline for a few weeks due to my 12V issue, and then being away for work... I'm due to get it replaced today (2nd attempt.. let's see if the dealer actually has a suitable battery this time!) at which point I can get the OVMS back in to experiment.</div>
<div><br></div><div>I'm pretty sure the EV bus is going to be a lot more useful to work with, especially in terms of battery/charging data so I'll be ordering a cable the instant I can! Thanks so much for getting the cable specced.</div>
<div><br></div><div>Nigel.</div></div><div class="gmail_extra"><br><br><div class="gmail_quote">On 16 June 2014 04:15, Mark Webb-Johnson <span dir="ltr"><<a href="mailto:mark@webb-johnson.net" target="_blank">mark@webb-johnson.net</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div style="word-wrap:break-word"><div><br></div><div>I've ordered a bunch of cables suitable for CAR and EV can buses of Nissan Leaf. Pinout is:</div>
<div><br></div><div><div><div style="font-size:12pt;font-family:Calibri"><div dir="ltr"><blockquote style="border:none;padding:0px"><div><font face="Andale Mono"><u>Pinout B</u></font></div><div><font face="Andale Mono"><br>
</font></div><div><font face="Andale Mono">J1962-M DB9-F Signal</font></div><div><font face="Andale Mono">4 3 Chassis/Power GND</font></div><div><font face="Andale Mono"><b>6 5 CAN-H (alternate CAN)</b></font></div>
<div><font face="Andale Mono"><b>14 4 CAN-L (alternate CAN)</b></font></div><div><font face="Andale Mono">13 7 CAN-H (primary CAN)</font></div><div><font face="Andale Mono">12 2 CAN-L (primary CAN)</font></div>
<div><font face="Andale Mono">16 9 +12V Vehicle Power</font></div><div><font face="Andale Mono"><br></font></div><div><font face="Andale Mono">J1962 end should be MALE plug with right angle cable. DB9 end should be FEMALE.</font></div>
<div><font face="Andale Mono">Both ends should be enclosed in shells, and cable should be 1metre in length.</font></div></blockquote></div></div></div></div><div><br></div><div>The wiring brings J1962-M pins 13 and 12 (EV can bus) through to our standard OVMS v2 can bus pins. It also brings the normal CAR can bus through on DB9-F pins 5 and 4 (for future use on any dual-can enabled OVMS module, or easy re-wiring at the DB9 end).</div>
<div><br></div><div>Cable itself as per our standard naming:</div><div><br></div><div><img height="85" width="93" src="cid:153443C7-0B5B-4D95-A34F-EC46E4FFBCC9"></div><div><br></div><div>For simplicity, I'll ask Fasttech to handle logistics for these, as usual.</div>
<div><br></div><div>Regards, Mark.</div><div><br></div></div><br>_______________________________________________<br>
OvmsDev mailing list<br>
<a href="mailto:OvmsDev@lists.teslaclub.hk">OvmsDev@lists.teslaclub.hk</a><br>
<a href="http://lists.teslaclub.hk/mailman/listinfo/ovmsdev" target="_blank">http://lists.teslaclub.hk/mailman/listinfo/ovmsdev</a><br>
<br></blockquote></div><br><br clear="all"><div><br></div>-- <br>----<br>Nigel Jones
</div>